Panel walls are a great way to add cubicle privacy to your work space. Most cubicle walls do not come with divider panels, therefore making it necessary to purchase them separately. These special wall partition panels can be hard to find at certain hardware stores so if you end up buying a few different ones before finding the right fit for you, it can get very expensive.
While this is old news to most, I’ve only really learned about how to build a panel wall recently. It’s not something I’ve ever learned before, “mdf wall panelling sheets”, “diy wall panelling” but it’s definitely something I’ll be using more of in the future. From what I can tell, there are three main ways to create a panel wall.
How to build a panel wall
If you’re looking for a simple, budget-friendly way to update your home, then MDF wall panelling is the perfect solution.
The panels are easy to install, they’re light in weight and they come in a variety of sizes and finishes. In addition to that, they’re incredibly sturdy and they can be used across different rooms of your house.
Here are some tips on how to build a panel wall:
MDF is a perfectly good material for building panels, but it’s not the only one. Panels can be made from many other materials, including plywood, chipboard and even solid wood.
The best way to build a panel wall is by using screws and glue to fix the panels together, then screwing them to the wall when you’re happy with their position (see above).
Panels are usually made from sheet material (usually 3-4mm thick) that’s been cut into strips and then glued together to make wider sheets. The strips are usually about 2m long so that they can be cut easily on a table saw or with a circular saw or jigsaw.
In this article we’ll look at how to build a panel wall from scratch using MDF. If you want to learn more about DIY wall panelling in general first, read our guide on how to install a DIY wall panelling system – it explains all the basics of installing DIY kitchen wall panelling.
MDF is a low-density material that’s made from wood chips and glue. It’s very easy to work with and cuts cleanly, which makes it a great choice for DIY projects. Here are a few tips for using MDF for paneling:
1. Make sure you have the right tools for the job. You’ll need a table saw or circular saw, as well as clamps and sandpaper. You may also need some other tools like a router, jigsaw and hammer drill.
2. Measure carefully before cutting your sheet of MDF into smaller pieces. The cut edges will be visible on the finished product, so make sure they look good!
3. Use biscuits or tongue-and-groove joints between panels to make them easier to install on your wall or ceiling surface. Biscuits create an interlocking joint between two pieces of wood. They’re glued in place before the panels are attached to each other with nails or screws through pilot holes drilled in each joint beforehand (see below). Tongue-and-groove joints are designed so that one piece fits into another exactly like a puzzle piece: When two pieces are put together, there’s no gap between them because one
The paneling used for this project is made of MDF (medium density fiberboard). This is a very durable material that can be painted or stained. It is also relatively easy to cut and install.
MDF comes in 4′ x 8′ sheets and can be purchased at most home improvement stores. The panels used in this project were 4′ x 10′ sheets that were pre-finished at the factory. This saves a lot of time and effort because you don’t have to stain the wood yourself.
The key to making sure your wall paneling looks great is to spend some time planning out how it will go together before you start cutting anything. You’ll want to plan on how many pieces of paneling you need, where they will go on the wall, what size they will be, etc…
You will need:
A wall to build the paneling on, a pencil, a ruler or measuring tape, masking tape (or blue tack), a Stanley knife (or other sharp craft knife) and an electric drill with a Phillips head bit.
Measure the height and width of your wall. Decide how many panels you wish to use (we made ours 4ft x 3ft). If your wall isn’t square measure it at the top and bottom of each side so that you can mark it accurately. Make sure your measurements are accurate as this will affect what size panels you cut.
Using your measurements as a guide mark out the size of each panel onto the wood blank. Make sure they line up evenly with each other as they are going to be butted against one another on the wall so no gaps should be left between them.
Drill holes into each corner of each panel with a 3mm drill bit – this will allow you to screw them onto the wall later on when you’re ready for that step!