Have you been looking for instructions on how to build a small wooden box? Curious about how to make a wooden box and wondering how to make a box with a lid? This is the only article you’ll need.
A wooden box is a relatively easy, but useful thing to make. There are countless uses for wooden boxes — from holding office supplies to shipping small items. With the right tools, supplies and techniques, you’ll be able to design and build one for just about any purpose.
How to build a small wooden box
A wooden box is one of those projects that has so many uses. It can be used as a gift box, a craft organizer, or even just to store your jewelry. This project should take you about an hour and require only basic woodworking skills.
2-inch wood screws (1 1/4-inch will work but may be too short)
Wood saw (jig saw optional)
Ruler or tape measure
Chisel or hammer and nail (for making pilot holes for the screws)
How to Make a Wooden Box with a Lid
Step 1: Cut the Wood
Cut two pieces of 3/4″ plywood that are 24″ x 12″ for the base and lid.
Step 2: Attach the Base and Lid Together
Glue the base to the lid, then clamp them together overnight.
Step 3: Sand and Stain
Sand all the edges, then stain the inside of the box. Let it dry for about an hour, then apply more stain to allow an even coat to develop. This is where I used a brush so that I could achieve an even coat with no drips down one side or another.
Step 4: Seal It Up!
Apply polyurethane on all sides of your box to give it a nice finish and protect it from moisture damage. This step is optional, but recommended if you plan on using your box outdoors or around water often.
Making a wooden box is easier than you think. Here’s how to make a simple box with lid, using just a few tools.
The first step is to decide what size you want your box to be. If you’re making a gift for someone special, then you’ll probably want it to be about the same size as their hands or something similar.
I like making boxes because they don’t take very long and there are so many different ways to decorate them.
In this tutorial I’m going to show you how to make a box with lid from start to finish, including cutting out the pieces and assembling them together.
Tools & materials needed:
Power drill/driver & screws (optional)
Tape measure & pencil
1 piece of scrap plywood – approx 10″ x 5″ (for the lid)
1 piece of plywood – approx 10″ x 12″ (for the bottom)
This is a simple guide on how to build a wooden box. We will be making the project from scratch, from buying the materials, cutting them and assembling them to give us our own DIY wooden box.
This project is for beginners who want to work on their woodworking skills and would like to start at ground zero. The process will be easy and simple as we will be using basic tools that anyone can get hold of and also costs less than $10.
Things You Will Need:
1. Sandpaper (60-80 grit)
2. Clamps or weights
3. Wood glue
4. Wood stain (optional)
5. Paint brush
Wooden boxes are a great way to store small items. They can be made in any size and shape, and there is no limit on the kinds of wood used. You can choose from dozens of different types of wood such as pine, oak, ash and poplar.
Some people like to make boxes out of solid wood boards, but most prefer plywood because it’s stronger and easier to work with. It’s also much less expensive than solid wood boards.
Building a box is a simple process that doesn’t require any special tools or skills other than knowing how to use a saw and drill. If you’ve never made anything with wood before, this is an excellent project for beginners.
How to Make a Wooden Box Frame
This is a quick and easy project that will make a nice addition to any home. The box frame is simple to make and can be used for many different purposes.
You will need:
Wooden or MDF board (8mm thick)
Wooden dowel rods (about 20mm diameter)
Glue or nails (for attaching the dowel rods)
Screws (for attaching the lid)
The frame of the box is made of pine wood and has a width of 16 cm.
The lid is made of oak and has a thickness of 5 mm.
Using the jigsaw, we will cut out the pieces for the box and lid.
We need to make 2 pieces each for the top and bottom of the box and 2 pieces each for the sides of the box.
The front piece should be 3 cm wide and 8 cm long. The back piece should be 2 cm wide and 9 cm long (width must be equal to thickness). The side piece should be 3 cm wide, 6 cm long, 3 cm high (height must be equal to half thickness) with an angle at one end. The other end must be cut in such a way that it fits into the corner created by two other side pieces.
Now we can assemble our wooden box frame using nails or screws (or both).
1. Measure the size of the box you want to make. Cut your wood to the correct dimensions.
2. Next, cut grooves into each side of each board. The grooves should be wide enough to fit a second piece of wood that will act as a lid for the box. If you have access to a router or table saw, use them instead of doing this manually with a chisel or coping saw (although this will take longer).
3. Next, attach the boards together using nails and/or screws (use at least 3 nails per board). The boards should be nailed/screwed together from one side only so that they can move freely when opening and closing the box (this is called “sliding dovetails”).
This is a tutorial on how to make a wooden box frame. The frame can be used for anything from jewelry and trinkets, to photos and art.
The first thing you need to do is cut the pieces of wood that will make up the box. Make sure you leave at least 1/4″ (0.64 cm) all around your design so that it fits into the groove.
Next, use an electric jigsaw with a fine blade to cut along the lines of your design. You may also be able to use a coping saw or fretsaw if you don’t have access to power tools. Don’t worry about getting it perfect yet; there will be plenty of time for that later!
After cutting all of your pieces out, sand them down with 80 grit sandpaper until they are smooth and shiny. This will remove any splinters or rough edges left by the sawing process, making it easier for painting later on!
Now take some 220 grit sandpaper and begin rounding off all corners and edges where paint might chip off easily later on in life! If you don’t have 220 grit, use 320 then 400… etc… until your corners are rounded off enough so that paint doesn’t chip off easily! You
Step 1: Cut the frame pieces. You will need four pieces of 1-by-4 pine. The length of the frame pieces should be twice the width of your photo, plus 1 inch (2.5 cm). For example, if your photo is 4 x 6 inches (10 x 15 cm), cut each piece to 8 inches (20 cm) long.
Step 2: Attach the sides together using glue and brad nails. Place two sides together with their long edges touching, then place a third side on top with its long edge facing outward at a right angle to the first two sides. Attach with glue and brad nails through all three pieces at each joint.
Step 3: Nail the remaining sides into place on top of one side already attached to create an enclosed box frame that is open at one end. Nail through all four pieces at each joint as before, but use only enough nails so that none can be seen from either inside or outside the box frame when it is assembled into its box shape later on.