If you want to build a porch overhang on your own there is no need to spend a lot of money on contractors. A good ides for you to follow might be this article from Designer blog about planning and building porch overhangs.

The purpose of this tutorial is to show you how to build a porch overhang so that you can enjoy outdoor living in your home or on your house. The reason I am writing this article is because while searching through the internet as I do, I found many great explanations on how to build a porch, but very little regarding building an overhang (note: an overhang is when the roof extends beyond a wall).

How to build a porch overhang

Building a porch roof overhang is simple, as long as you follow a few simple steps. This article will guide you through the process of building your own porch roof overhang.

Materials Needed:

Plywood sheets – One sheet can make four overhangs depending on its size. Use the plywood sheets to create the sides of the overhang. The size depends on how much area needs to be covered by the overhang and what kind of door or window is installed in front of it.

Corrugated steel sheets – Use these for making the top part of the porch roof overhang because they are strong enough and durable enough to withstand the elements like rain, snow and wind.

Screws (to attach plywood base) – You will need these screws if you want to attach your plywood base to concrete or stucco walls using predrilled holes in them or if you want to secure each corrugated steel sheet onto its respective plywood base before attaching them together side by side into one unit that can be lifted up from underneath with ropes attached to each corner joint between them since this

How to build a porch roof step by step

Step 1: Plan the layout of your roof.

The first step in building a porch roof is to decide what shape it will be. If you’re building a small porch, you’ll probably want a simple gable shaped roof with an overhang on the eaves and soffits. If you’re building a larger porch, you may want to add dormers or other features.

Step 2: Attach rafters over the walls of your structure.

The next step in building a porch roof is to attach rafters over the walls of your structure. To do this, measure from each corner of the house down to where you want the top edge of your overhang to be and mark these spots on each wall. Then use your tape measure to find out how long each rafter needs to be and cut them accordingly using your circular saw or jigsaw (if they’re too long).

Step 1: Determine the size of your overhang.

Step 2: Measure and cut the rafters.

Step 3: Build the roof frame.

Step 4: Install the roofing material.

Step 5: Build the stairs and rails for your porch roof.

How to Build a Porch Roof Overhang

Building a porch roof overhang is one of the easiest projects you can do on your house. It doesn’t require any special tools, just some basic carpentry skills and a little bit of patience.

Step 1:

Measure the length of your porch and decide how much overhang you want on each side. The average overhang is about 6 inches, but you can go as big as you want.

Step 2:

Cut two pieces of trim molding to fit between the top edge of the porch floor and the bottom edge of your fascia board. These pieces should be about 24 inches long, with an angle cut at each end so they fit flush against the fascia board and floor joists. You can find pre-cut lengths of trim molding at any home improvement store or lumber yard, or make your own by ripping down strips from wider boards using a table saw or circular saw with rip fence attachment.

Step 3:

Set up a level on each side of your porch and mark where it hits the floor joist below (or use a laser level if you have one). This will tell you where to screw in screws that will hold your new trim mold

Porch roof overhangs are a great way to add style and function to your home. A porch roof overhang offers protection from the rain and sun, making it a great place to sit and relax on a hot summer day. Porch roof overhangs are also a great way to add curb appeal to your home, as they provide shade and can create an inviting atmosphere for visitors.

Porch Roof Overhangs

A porch roof overhang is basically the same thing as an eave, which is the lower edge of a pitched roof that projects beyond the supporting wall of a building or structure. The purpose of an eave is to protect walls from rainwater and snowmelt, as well as provide shade in hot weather. Porch roofs can be designed with many different styles of eavesto fit any architectural style. For example, gabled roofs have triangle-shaped eavesthat come together at their peak; shed roofs have slanted eaves that come together at their peak; hip roofs have vertical eaves that come together at their hips; and mansard roofs have flat eaves that come together at one corner of each side of the building.

Eaves differ from cornices because they extend outward beyond the face of the wall (whereas